Jims

146 products

JIMS motorcycle tools are available for adjusting clutches, installing exhaust gaskets, removing camshafts, aligning ignitions and much more. Browse the range below!

Sold Out

JIMS

$565.99

Kit Includes: * 1 – 24006-80/83, Pinion shaft * 1 – 2196, Metered oil jet screw * 1 – 24016-80, Flywheel side nut * 1 – 2187, (HD # 11218), Flywheel side key * 1 – 2480, (HD # 23985-54), Pinion ge...

Sold Out

JIMS

$407.99

* All ground diameters are concentric to within .0003″ to simplify flywheel trueing and rebuilding * Constructed of only domestic steel * Replaces OEM # 24006-58 * Made in the U.S.A.

JIMS

$530.99

A tool that every engine builder needs. This tool properly tests the pressure rating of each piston oiler jet before you final assemble your engines.

JIMS

$510.99

Features & Benefits:- * Fits all H-D Models. * Supplied with six bands. * Works with piston sizes from 2-7/8″ to 4-3/8″. * Fine-tooth ratcheting motion will compress the bands in small increme...

JIMS

$426.99

Features & Benefits:- * Run in cast iron or aluminum tappet blocks * Produced from billet bearing steel * A true center-line for roller life and exact cam timing * State of the art pushrod sea...

Sold Out

JIMS

$986.99

Features & Benefits:- * Fit all Big Twins with Shovel Engines using JIMS Powerglide Tappets #’s JM-2459-1, JM-2460-1 or JM-2461-1. * Upgrade to the latest design improvements. * Kit comes wit...

Sold Out

JIMS

$205.99

A primary lock bar is key in locking the primary drive system on Harley-Davidson® motorcycles. JIMS® lock bars are made from aircraft quality steel and plated in black oxide for corrosion resistan...

JIMS

$200.99

* Used to lock primary for service work * Fits between the chain and motor sprocket * Works on all 5 speed primaries * Made out of black Delrin® * Made in the U.S.A.

JIMS

$330.99

Features & Benefits:- * Race & Bearing Driver Handle Tool. * Use Handle with #’s JM-33071-73, JM-34810-84, JM-94547-80A, JM-94547-80B, JM-97272-60 & JM-97273-60. * Approximately 12″ l...

JIMS

$427.99

* Reduces shifter free play * Assembly includes plate (replaces OEM #35068-79) * Spring (#34087-79) * Pawl plate (#34086-79) * Shifter shaft (#34084-86) * Spring (#34083-79) * Pin (#34082-79) * Wa...

JIMS

$265.99

Features & Benefits:- * Replacement 25mm Puller Only. Proudly Made in the USA by JIMS !

JIMS

$355.99

Features & Benefits:- * Removes & installs the 25mm H-D bearing. * Removes ABS or non ABS Wheel Bearings on most of 2008up Wheels. * This tool must be used with the earlier JIMS wheel bear...

Sold Out

JIMS

$243.99

Features & Benefits:- * Replacement Jims Wheel Bearing Puller .750in. I.D. Proudly Made in the USA by JIMS !

JIMS

$281.99

Fitment Note: 2006-2017 Dyna & 2007up Models:- The bearing race is installed from factory with RED Locktite along with the trans pulley nut. This has been causing some problems. The two items...

Sold Out

JIMS

$221.99

Features & Benefits:- * These bushings are manufactured from solid billet bearing bronze bar stock. * Ream to fit. Use JIMS# tool No.95760-57 for removal, No.2357 for installing and No. 94804...