Jims

142 products

JIMS motorcycle tools are available for adjusting clutches, installing exhaust gaskets, removing camshafts, aligning ignitions and much more. Browse the range below!

JIMS

$964.99

Tappet Pump and Test Stand * Helps diagnose loose or spongy tappets that could eventually lead to bleed-down issues or sticky tappets that won’t pump up due to poor hydraulic unit fitment * Allows...

Sold Out

JIMS

$290.99

Features & Benefits:- * Use in cast iron or aluminum tappet blocks. * Produced from billet bearing steel. * Increases roller life. * exact cam timing. Tech Tips:- * Recommend tappet to block ...

JIMS

$3,890.99

Features & Benefits:- * Suggested additional purchase, Timken Bearing # SS31-4013 Tech Tips:- * May cause a slight increase in engine noise MFR PART No: 959 ROLLIES PART No: JM-959

JIMS

$368.99

* Used for removing and installing the Timken® bearing outer race snap ring. * A must for replacing rings in OEM and aftermarket cases * Made in the U.S.A. MFR PART No: 1710 ROLLIES PART No: JM-...

JIMS

$493.99

Installing fork tube caps requires compressing the spring while rotating the cap. This is not particularly difficult with fork legs that have been removed from the bike and securely mounted in a ...

JIMS

$310.99

35mm Slider tube top cap nut. Use’s 3/8″ drive * Used to remove and install top fork nuts on fork tubes * Rubber protector inside socket protects chrome finish * Will clear under most handlebars *...

Sold Out

JIMS

$250.99

* Used to remove and install top fork-tube plug * Fits 41mm forks * Made in the U.S.A * Note: this tool works on the top fork plug that screws into the fork tube. * Slider tube cap socket JM-2244...

JIMS

$1,915.99

Features & Benefits:- * M8 cylinders require Torque Plates to be accurately honed & measured * Simulates operating stress conditions when boring or honing the cylinders. * Adapt easily ...

JIMS

$1,055.99

Features & Benefits:- * Kit Includes JIMS proven transmission parts topped off with a Jims Gasket set, together in one convenient package. * This is a big time saver. * Made in the U.S.A. Te...

JIMS

$276.99

* Standard O.D. is 2.314″, I.D. is 1.8802″. * It will depend on the amount of press fit and will determine the amount of line lapping required to fit new bearing and mainshaft. * Replaces OEM # 3...

JIMS

$275.99

Standard O.D. is 1.5635#, I.D. is 1.3045#. The amount of the press fit in the trans case will determine the amount of line lapping required to fit new bearing and mainshaft. Use JIMS# Tool No.3481...

Sold Out

JIMS

$593.99

* Lock your transmission pulley for removing or installing pulley nut * Fits OEM & Aftermarket 5 & 6 speed transmissions. * Made in the U.S.A. Tech Tips:- * Does NOT fit Sportster Models (...

JIMS

$641.99

* Inner collar will retain wrench to nut for safer work * Remove hex nut from end of main drive gear that secures the rear drive transmission pulley * Extra-long two-piece design * Made in the U.S...

JIMS

$643.99

Features & Benefits:- * Fits 4 & 5 Speed Models * Heavy-Duty thick wall tube. * Extra long two piece design, inner collar will retain wrench to nut for safer service work. * 1-7/8″ hex. *...

Sold Out

JIMS

$269.99

Features & Benefits:- * Short Socket. * Designed to Remove, Install & Properly Tighten the Front Final Drive Sprocket/Pulley Nut. * Although the much longer Big Twin socket will fit the nu...